顶固分公司 > 产品营销 > P系列精铸不锈钢大门锁 > 产品信息

上一个产品：P9076MAC DT欧式豪华插芯锁     

产品保养：

1、安装锁具前要仔细阅读说明书，特别注意的是，在没有刷油漆前开孔，油漆干后才将锁安装上。千万不要在油漆未干就装门锁。油漆的挥发性气体会减少锁的使用寿命。

2、锁具在平日开关门的过程中，最好握着执手把锁舌旋进锁体，关好门后再松手，不要用力撞门，否则会减少使用寿命。锁具使用一段时间后，会出现开启不顺畅的现象，不要往锁心内滴机油，将滑石粉或铅笔心的细屑滑入锁心内即可。

3、另外，不要用湿布擦拭锁体和执手，因为有些金属材质的锁具会因此生锈；合金材质的锁具会将镀层磨掉，失去美观的效果。

Lock maintenance of products:

1、Read carefully the specification of the lock before use. Note that if punching hole before being painted, then do not install the lock until the paint is dry. Never install it before the paint gets dry. The volatile gas of the paint can reduce the useful life.

2、In everday use, it is best to hole the handle to insert the lock-tongue into the lock. Do not let off until the door is closed. Do not bang the dcor, otherwise it would reduce its useful life. When used for a time, the lock may not be opened smoothly. Do not dip mechanical oil into the lock. Instead, slip some French chalk or pencil fines into it.

3、In addition, do not use wet cloth to wipe the lock and handle, because some metallic lock might get rusted. The alloy lock may

  

豪华欧版锁产品特点：

1、适应门厚45-60mm，

2、使用场所：豪宅、工程配套、写字楼等

3、配置专利夜光锁头、精铸不锈钢锁芯拨件

4、表面处理：棕古（MAC）

5、面板规格: 580*68（长X宽）,豪华型风格

6、锁体规格：64X87A(衬板至锁头孔距离X锁体方芯孔至锁头孔距离)

7、铜衬板，铜锁方舌，铜斜舌，铜执手拨动件

8、执手面板采用澳洲3#锌合金材料制作,结合特殊的多层电镀工艺，色泽持久、手感细腻，耐腐蚀性能优良，盐雾实验时间远远超过国标要求的24小时,再经硬度4H以上的清漆封闭，烤漆温度达150℃；表面光滑，大大提高了防腐，防划伤能力。且不沾灰尘油污。

 

European-lock features:

1、thickness of the door：45-60mm

2、site of use：the great house，accompany engineering and office building etc

3、equipped with the patent noctilucent cylinder，and refined casting stainless steel plug follower

4、surface treatment：MAC

5、faceplate specification：580×68（length×width）；deluxe style

6、lock body specification：64×87A（the distance from scaleboard to cylinder hole×the distance from square plug hole of lock body to cylinder hole）.

7、copper scale board, copper lock bolt ,copper  lever handle follower ;

8、Keep the hand face plate 3# zinc in Australia  alligation material manufacture, combining many special lamellas  plating craft, the color and luster endure, the feeling of hand is delicate, bearing to decay the function good, the salt fog  experiment time marks 24 hours of request far above the country far, again through the 4 Hs of hardness  above varnish seal, roast to paint the temperature to amount to 150 ℃s;The surface is smooth, raising the antisepsis consumedly, defending the scoring, scuffing ability.And don't be stained with the greasy dirt of dust.

 

安装步骤：

A.        确定开门方向后，调整斜舌方向，根据安装纸规，并在门上按照特定的高度定位，依照纸规上的定位点及所要求的尺寸在门上做好标记。按标记在门厚中间凿槽，从门面上钻孔。

B.         将锁体插入已开好孔的门扇，

C.         并上紧锁体固定螺丝；

D.        将圆头螺丝及垫圈从方轴上移走，将方轴从后面板方向水平插入锁体方形孔至外部。重新放入垫圈，并且重新从外部上紧圆头螺丝。

E.         安装前面板， 退少许锁头调节螺钉。（以锁头能旋入为准）使锁头穿过前面板与锁体安装位置对准，旋转锁头进入，旋紧锁头调节螺钉。

F.         将固定螺丝穿过后面板固定前面板。旋上装饰盖。

G.         转动把手，使方舌伸出，然后上紧锁体面板上螺丝。安装门扣盒和门扣板，使锁具开启顺畅。

Installation steps:

A.        Determine the opening direction of the door, then adjust the ramp tongue. According to the regulation permits, position it on the door at the specified height. In accordance with the regulation permits, the positioning points and the required size are marked on the door. By marking the doors thick middle fluting, then drill on the door leaf.

B.         Insert the lock body into door leaf,

C.         Screw down the fixing screws.

D.        Remove the round-head screws and washer from the side axis. The axis of side direction from the panel after insertion level lock-square hole to external. Add new washers and re-tightened from external head screwdriver

E.         Install the panel. Retreat a little adjustment screw lock. (Locks can be rotated into whichever is fine) so that the first through the lock front panel lock installation and alignment, rotation lock first entry, Rotary merely adjusting screw head

F.         Insert the fixing screws through  the back panel to tighten the front panel.  install the decorative cover.

G.         Turn the handle and make the tongue stick out, then screw down the screws.

H.        Install the door holder box and door holder plate, to make locks open smoothly.

 

本站首页 | 关于我们 | 历史文章 | 网站地图 | Google Sitemap | 信息反馈 | 时代财富网 | 网站建设 | 登录管理